menu
PVC PRODUCTS
PVC CORE PIPE

PVC CORE PIPE

◎ Pressure-resistant, waterproof
◎ Pest control
◎ To take up tape or various films
◎ Length thickness customizable

APPLICATIONS:

Used by the plastics industry for rolled plastic sheets, rubberized cloth, adhesive, and other applications.

Share :
SPECIFICATION
VU(A) Outer diameter, thickness and tolerance difference
unit：mm
Pipe
diameter		 Outside Thickness Reference
Flanges Outside diameter(a) Least Tolerances Inner diameter Quality(b)
kg/m
40 48.0 ±0.2 1.8 +0.4 44 0.413
50 60.0 ±0.2 1.8 +0.4 56 0.521
65 76.0 ±0.3 2.2 +0.6 71 0.825
80 89.0 ±0.3 2.7 +0.6 83 1.159
90 100.0 ±0.4 3.1 +0.6 94 1.476
100 114.0 ±0.4 3.1 +0.8 107 1.737
125 140.0 ±0.5 4.1 +0.8 131 2.739
150 165.0 ±0.5 5.1 +0.8 154 3.941
200 216.0 ±0.7 6.5 +1.0 202 6.572
  • NOTE：
  • (a)The average tolerance of outer diameter refers to the value obtained by dividing the measured value of the circumference on any cross-section by the circumference ratio (3.142), or the deviation between the average measured value of the outer diameter at two equal intervals on the circumference (average outer diameter) and the basic dimension.
  • (b)The mass per unit length in the table is set at the midoint of the tolerance based on the size of the tube, and calculated with the density of VP as 1.43g/cm3.
VP(B) Outer diameter, thickness and tolerance difference
unit：mm
Pipe
diameter		 Outside Thickness Reference
Flanges Maximum, minimum outer diameter Tolerances(a) Outside diameter(b) Least Tolerances Inner diameter Quality(b)
kg/m
13 18.0 ±0.2 ±0.2 2.2 +0.6 13 0.174
16 22.0 ±0.2 ±0.2 2.7 +0.6 16 0.256
20 26.0 ±0.2 ±0.2 2.7 +0.6 20 0.310
25 32.0 ±0.2 ±0.2 3.1 +0.8 25 0.448
30 38.0 ±0.3 ±0.2 3.1 +0.8 31 0.542
40 48.0 ±0.3 ±0.2 3.6 +0.8 40 0.791
50 60.0 ±0.4 ±0.2 4.1 +0.8 51 1.122
65 76.0 ±0.5 ±0.3 4.1 +0.8 67 1.445
80 89.0 ±0.5 ±0.3 5.5 +0.8 77 2.202
100 114.0 ±0.6 ±0.4 6.6 +1.0 100 3.409
125 140.0 ±0.8 ±0.5 7.0 +1.0 125 4.464
150 165.0 ±1.0 ±0.5 8.9 +1.4 146 6.701
200 216.0 ±1.3 ±0.7 10.3 +1.4 194 10.129
  • NOTE：
  • (a)The tolerance between the maximum and minimum outer diameters refers to the deviation between the maximum and minimum (maximum and minimum outer diameters) measured value on any cross-section of the outer diameter and the basic dimension.
  • (b)The average tolerance of outer diameter refers to the value obtained by dividing the measured value of the circumference on any cross-section by the circumference ratio (3.142), or the deviation between the average value of the outer diameter measured at two equal intervals on the circumference (average outer diameter) and the basic dimension.
  • (c)The mass per unit length in the table is set at the midoint of the tolerance based on the size of the tube, and calculated with the density of VP as 1.43g/cm3.
E Pipe size and its allowable difference
unit：mm
Pipe
diameter		 Outside diameter(a) Thickness Inner diameter Quality(b)
(kg/m)		 Length
Least Tolerances
13 18±0.2 1.8 +0.4 14 0.144 Marked value
+30
-10
16 22±0.2 1.8 +0.4 18 0.180
20 26±0.2 1.8 +0.4 22 0.216
28 34±0.3 2.7 +0.6 28 0.420
35 42±0.3 3.1 +0.8 35 0.608
41 48±0.4 3.1 +0.8 41 0.702
52 60±0.5 3.6 +0.8 52 1.010
65 76±0.5 4.1 +0.8 67 1.450
80 89±0.5 5.1 +0.8 78 2.070
100 114±0.6 6.6 +1.0 100 3.420
125 140±0.8 7.0 +1.0 125 4.490
150 165±1.0 8.5 +1.4 148 6.460
200 216±1.3 10.5 +1.4 194 10.340
  • NOTE：
  • (a)The outer diameter refers to the arithmetic average of the outer diameters in any two vertical directions.
  • (b)The calculation of mass is based on the minimum thickness plus half tolerance of thickness as the calculation of thickness with the density. 1.43g/cm3.
ES-1 Pipe size and its allowable difference
unit：mm
Pipe
diameter		 Outside diameter(a) Thickness Inner diameter Quality(b)
(kg/m)		 Length
Least Tolerances
80 89±0.5 2.7 +0.6 83 1.160 Marked value
+30
-10
100 114±0.6 3.6 +0.8 106 1.980
125 140±0.8 4.1 +0.8 131 2.750
150 165±1.0 5.1 +0.8 154 3.960
  • NOTE：
  • (a)The outer diameter refers to the arithmetic average of the outer diameters in any two vertical directions.
  • (b)The calculation of mass is based on the minimum thickness plus half tolerance of thickness as the calculation of thickness with the density. 1.43g/cm3.
DOWNLOAD